Shindaiwa EC7600 Manual del operador Pagina 7
- Pagina / 84
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
20 mm
Collar
22mm
Collar
25.4mm
Collar
Snap
Ring
Flange
Collar
Drive
Shaft
7
WARNING!
Use of the incorrect collar
size may lead to wheel failure and unit
failure that could result in serious injury.
Assembly
Figure 6
Instruction
Manual
Engine Unit
Tool Set
Figure 8
Belt Guard
Hex Wrench
Select a cut-off wheel for your work
according to the following chart. Refer
to the wheel manufacturer’s manual for
additional information.
Make sure the ON-OFF switch is Off
and the engine is stopped.
1.
2.
Before assembling, make sure you have
all the components required for a com-
plete unit. This unit consists of the items
shown in Figure 6.
Carefully inspect the engine unit for
damaged or loosen bolts. If you find any
damage or missing items, check with your
Shindaiwa dealer.
IMPORTANT!
This unit is equipped with a 22mm wheel
collar. Wheel adapters for 20mm and 25.4mm
cut-off wheels are located in the tool set.
Before mounting a wheel, determine its
arbor diameter. If it is necessary to replace
the collar, remove the snap ring on the arbor,
install the correct size arbor collar, and then
replace the snap ring.
Place cut-off wheel so the inner bore is
properly set onto the collar.
5.
Figure 9
Outer Flange
Bolt
Tighten
Loosen
Replace outer flange and bolt, and then,
while holding hex wrench in the hole in
belt guard, tighten the bolt with wrench.
Make sure the cut-off wheel is securely
fastened. Spin the wheel to make sure it
does not wobble.
6.
7.
WARNING!
Using an inappropriate cut-off
wheel may cause the wheel to break
and may result in serious injury.
Recommended cut-off wheels
Internal
diameter
.79 in., .87 in., 1.0 in./
20 mm, 22 mm, 25,4 mm
Discs for
model
EC7500 EC7600
Abrasive: outer diameter
12 in./305 mm
outer diameter
14 in./355 mm
Diamond:
outer diameter
12.6 in./320 mm
outer diameter
14.2 in./360 mm
Prior to assembly
Mounting the Cut-off Wheel
Insert a hex wrench into the hole in the
belt guard to prevent the arbor from
turning. See Figure 8.
Loosen bolt with the wrench and remove
bolt and outer flange. See Figure 9.
3.
4.
Figure 7
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals.es. Todos los derechos reservados | 0.150 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales