Shindaiwa EC7600 Manual del operador Pagina 11
- Pagina / 84
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
11
WARNING!
When using the cut-off saw,
the wheel guard must be securely
in position as a protection against a
broken wheel. If the wheel guard is
not in place, a broken wheel could
project fragments at high speed
and strike you or others, possibly
resulting in serious injury.
This unit is designed to be operated for
either dry or wet cutting. A water dust-
suppression kit is available for this unit
but is not supplied in the unit packaging.
Please refer to the assembly and operating
instructions supplied with the water dust-
suppression kit.
Operation
This unit performs most efficiently when
cutting between 8,500 and 9,500 min
-1
(rpm). While running the engine at full
throttle, apply slight pressure to the cut-
off wheel against an object so that engine
speed stays at 8,500–9,500 min
-1
(rpm).
Too much pressure to the wheel will lower
wheel speed, reducing cutting efficiency
considerably.
Figure 15
Wheel Guard
Lock Knob
Wheel Guard
Locked
Wheel Guard
Free
WARNING!
Never permit bystanders or animals
near the unit when starting or
operating the unit.
Be aware of kickback! Kickback
may force the cut-off wheel up and
back toward the operator lightning-
fast. Kickback can occur whenever
■
■
the upper half of the cut-off wheel
touches an object. Never cut an
object using the upper-half of the
cut-off wheel.
When operating, always wear
snug-fitting clothing, safety gloves,
safety non-skid footwear, hearing
protection, a dust-proof mask, a
helmet and goggles.
■
Adjust the position of the wheel guard
so that fragments will not fly toward you
if the wheel fractures. To reposition the
wheel guard, loosen the lock knob (coun-
terclockwise). When the wheel guard is
positioned correctly, securely tighten the
lock knob. See Figure 15.
Make sure you have a clear work area
and secure footing.
Position the cut-off wheel vertically to
an object. Start cutting at a low speed
and then gradually accelerate the speed.
1.
2.
Cutting
Wet or Dry Operation
Adjusting Wheel Guard Angle
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales